Developing a better band saw blade for cutting difficult-to-cut materials requires a groundup approach
Above: The Advanz TS carbide-tipped band saw blade is suitable for sawing difficult-to-machine metals
Developing a better band saw blade for cutting difficult-to-cut materials requires a groundup approach
August 2022- Band saw blades have evolved over the years as the types of workpiece materials they cut have changed. In decades past, most service centers cut carbon steel, according to Jay K. Gordon, North American sales manager for saws and hand tools at The L.S. Starrett Co. in Athol, Massachusetts.
To meet the challenges of sawing more difficult-to-machine materials that service centers began seeing more of, band saw machine builders introduced more rigid and accurate equipment, he adds. Blade manufacturers were faced with the same challenges and needed to design and produce blades that not only could cut straighter and last longer, but they also had to cut more smoothly to eliminate secondary milling operations and reduce scrap. One of the results was more productive bi-metal blades.
Bi-metal band saw blades effectively cut some stainless and tool steels, as well as carbon steel, Gordon says, but cannot perform at the same level when sawing challenging exotic and aerospacegrade materials, such as nickel-based superalloys. The applications for those types of metals had previously been few and far between. “Now they are becoming the norm for everybody, the big and small shops and everyone in between.”
DO LOOK BACK
Although a well-established product category, carbide-tipped blades required enhancements to saw these challenging materials to the specified tolerances, Gordon notes. Developing a better blade to handle such materials requires a ground-up approach, starting with the backer—the foundation of any blade. The backer must provide the beam strength and flexibility to twist through the guides while rotating around the band wheels hundreds or thousands of times without cracking. Adding chrome or nickel, for example, to the backer enhances flexibility and the ability to withstand the higher feed force required to cut exotics.
That backer will differ based on the application. For example, a blade made to saw aluminum, where the cutting speeds are significantly higher than when sawing superalloys, won’t have the same backer as a blade for cutting Inconel, according to Gordon. “The forces that the backer has to withstand are completely different. It’s not a one size fits all.”
The carbide grade also varies based on the application. “There are multiple grades,” Gordon says, “and they all provide different levels of performance.”
To help determine the appropriate grade, Starrett consults with its carbide suppliers, he adds. When sawing a very hard metal, the carbide grade must be less prone to chipping and withstand the high level of heat at the tool/ workpiece interface.
In addition, Starrett frequently develops new grades as part of its R&D efforts, focusing on ones for the nickel-base superalloy market, Gordon says. “We have a team specific to carbide research and development. We’ve found it important enough that we have split off an R&D team to focus on nothing but carbide.”
Most service centers are keen to know what to look for when selecting the best carbide- tipped band saw blade for an application. Gordon cites a carbide-tipped blade with a multiple-chip grind and high/low tooth sequence that produces more chips spread out over more teeth, boosts productivity and extends tool life when sawing harder materials compared to alternative designs.

The Advanz MC7 utilizes a progressive four-tooth grind, which creates seven distinct chips to reduce wear compared to blades with a conventional triple chip tooth formation.
In addition, a multi-chip grind reduces the chip load per tooth and the stress exerted on each tooth. “It spreads the load,” he says.
Gordon adds that chip load is one of the primary causes of all blade wear. “If you’re trying to cut too fast with any of them, you increase the load per tooth and that brings it up into the danger zone, and that’s where you start wearing teeth.”
LET’S GET ROCKING
Gordon recommends blades that include a “backgrind” technology. Starrett’s AMP technology has a custom back-edge enhancement on the blade that generates a rocking motion while cutting, especially for hard-to-cut materials. The back of the blade is where the teeth are located, and the back is typically straight, he says. “When you do a backgrind, you are literally putting a wave on the back of the blade.”
The rocking motion helps prevent the teeth from overloading and minimizes the surface contact area to extend blade life, Gordon adds. “The blade is going to dig into a smaller piece of material, and that allows for better chip release and a higher production rate.”

RAKE ANGLE: The Advanz MC7 features Starrett’s unique tooth geometry, which has a progressively ground trapezoidal design and positive rake angle. The toolmaker’s edge preparation reportedly minimizes microchipping.
Blade pitch, width and tooth set design are additional critical factors to consider. Because the number of teeth that contact the workpiece can negatively impact both the blade performance and life, tooth pitch, defined by the number of teeth per inch, must be properly selected, Gordon explains. Too few teeth in contact with the work can lead to tooth strippage, and too many teeth can significantly reduce cutting rates to where blade is rubbing down rather than biting into the material and, ultimately, the material becomes impossible to saw.
“The rule of thumb is no fewer than three teeth in material at all times,” Gordon says of the startingpoint recommendation. The maximum number is about 15 to 22 teeth, depending on the workpiece material. “The finer the tooth blade and the bigger the piece of material that you have, the more likely it is to load, except for very hard materials. There are always exceptions to every rule.”
BAD VIBRATIONS
When there is uniform distance from one tooth tip to the next tip and all teeth have a uniform gullet depth and rake angle, the blade has a constant pitch, which can increase harmonic vibrations, Gordon says. “Vibration kills carbide. The advantage to carbide is it is very hard.
The disadvantage to carbide is that it is very hard.” To minimize the amount of vibration that is detrimental to the hard yet brittle blade material, variable-pitch blades have long become the industry standard, he notes. “You are unlikely to set up harmonics with a variable-pitch blade as opposed to a straight-pitch blade.”
By varying the tooth spacing, sawing rhythms are interrupted to reduce vibration, chip evacuation is improved, and less noise is generated. Variable-pitch blades are effective for sawing structural, tubing and solids, according to Starrett. Nonetheless, constant-pitch blades are still available, with the casting industry commonly using them to manually saw gates, risers and similar pieces with blades made of high-speed steel, Gordon adds, noting, “The casting industry is one of the few I see using straight-pitch blades.”
For blade width, all production-type saws or any saw that can run carbide-tipped blades are designed to use one specific blade width size, primarily due to band saw size and blade guide size, he notes. “Until you get down to the small job shops that are using very small machines, it is very unusual to have the ability to change widths.”
Tooth set is the side-to-side bending of the teeth, left and right.Starrett reports that the set provides clearance for the blade to move through the cut by helping to evacuate chips. The tooth set can also affect how efficiently the blade cuts and the quality of the surface finish. Gordon says the vast majority of blades have a raker set, with three teeth in a recurring group: one bent left , one bent right and one that is not bent. Another common tooth set is alternate, where the teeth are bent evenly right and left .
As workpiece materials continue to evolve, band saw blade manufacturers continue to fine-tune and upgrade their offerings to keep pace. When an end user runs into a production bottleneck or finds its blades dulling prematurely, leaving crooked cuts and imparting a poor surface finish, is when Starrett typically gets a call and becomes involved, Gordon says.
The objectives can vary. “Some end users want the best [blade] life they can possibly get, and they give up some production,” he says. “Others want the best production possible, and they will give up some life. It’s always best to first understand what the customer’s objectives are.” MM

